access to a list of parameters, with management of read stage (owned parameters, properties, associativities) and current parameter number, read errors (which feed a Check), plus convenient facilities to read parameters, in particular : More...

#include <IGESData_ParamReader.hxx>

Public Member Functions
	IGESData_ParamReader (const Handle< Interface_ParamList > &list, const Handle< Interface_Check > &ach, const Standard_Integer base=1, const Standard_Integer nbpar=0, const Standard_Integer num=0)
	Prepares a ParamReader, stage "Own", current param = 1 It considers a part of the list, from <base> (excluded) for <nbpar> parameters; <nbpar> = 0 commands to take list length. Default is (1 to skip type) More...

Standard_Integer	EntityNumber () const
	Returns the entity number in the file. More...

void	Clear ()
	resets state (stage, current param number, check with no fail) More...

Standard_Integer	CurrentNumber () const
	returns the current parameter number This notion is involved by the organisation of an IGES list of parameter : it can be ended by two lists (Associativities and Properties), which can be empty, or even absent. Hence, it is necessary to know, at the end of specific reading, how many parameters have been read : the optional lists follow More...

void	SetCurrentNumber (const Standard_Integer num)
	sets current parameter number to a new value must be done at end of each step : set on first parameter following last read one; is done by some Read... methods (must be done directly if these method are not used) num greater than NbParams means that following lists are empty If current num is not managed, it remains at 1, which probably will cause error when successive steps of reading are made More...

IGESData_ReadStage	Stage () const
	gives current stage (Own-Props-Assocs-End, begins at Own) More...

void	NextStage ()
	passes to next stage (must be linked with setting Current) More...

void	EndAll ()
	passes directly to the end of reading process More...

Standard_Integer	NbParams () const
	returns number of parameters (minus the first one) following method skip the first parameter (1 gives the 2nd) More...

Interface_ParamType	ParamType (const Standard_Integer num) const
	returns type of parameter; note that "Ident" or "Sub" cannot be encountered, they correspond to "Integer", see also below More...

Standard_CString	ParamValue (const Standard_Integer num) const
	returns literal value of a parameter, as it was in file More...

Standard_Boolean	IsParamDefined (const Standard_Integer num) const
	says if a parameter is defined (not void) See also DefinedElseSkip More...

Standard_Boolean	IsParamEntity (const Standard_Integer num) const
	says if a parameter can be regarded as an entity reference (see Prepare from IGESReaderData for more explanation) Note that such a parameter can seen as be a plain Integer too More...

Standard_Integer	ParamNumber (const Standard_Integer num) const
	returns entity number corresponding to a parameter if there is otherwise zero (according criterium IsParamEntity) More...

Handle< IGESData_IGESEntity >	ParamEntity (const Handle< IGESData_IGESReaderData > &IR, const Standard_Integer num)
	directly returns entity referenced by a parameter More...

IGESData_ParamCursor	Current () const
	Creates a ParamCursor from the Current Number, to read one parameter, and to advance Current Number after reading. More...

IGESData_ParamCursor	CurrentList (const Standard_Integer nb, const Standard_Integer size=1) const
	Creates a ParamCursor from the Current Number, to read a list of "nb" items, and to advance Current Number after reading By default, each item is made of one parameter If size is given, it precises the number of params per item. More...

Standard_Boolean	DefinedElseSkip ()
	Allows to simply process a parameter which can be defaulted. Waits on the Current Number a defined parameter or skips it : If the parameter <num> is defined, changes nothing and returns True Hence, the next reading with current cursor will concern <num> If it is void, advances Current Position by one, and returns False The next reading will concern <num+1> (except if <num> = NbParams) More...

Standard_Boolean	ReadInteger (const IGESData_ParamCursor &PC, Standard_Integer &val)

Standard_Boolean	ReadInteger (const IGESData_ParamCursor &PC, const Standard_CString mess, Standard_Integer &val)
	Reads an Integer value designated by PC The method Current designates the current parameter and advances the Current Number by one after reading Note that if a count (not 1) is given, it is ignored If it is not an Integer, fills Check with a Fail (using mess) and returns False. More...

Standard_Boolean	ReadBoolean (const IGESData_ParamCursor &PC, const Message_Msg &amsg, Standard_Boolean &val, const Standard_Boolean exact=Standard_True)

Standard_Boolean	ReadBoolean (const IGESData_ParamCursor &PC, const Standard_CString mess, Standard_Boolean &val, const Standard_Boolean exact=Standard_True)
	Reads a Boolean value from parameter "num" A Boolean is given as an Integer value 0 (False) or 1 (True) Anyway, an Integer is demanded (else, Check is filled) If exact is given True, those precise values are demanded Else, Correction is done, as False for 0 or <0, True for >0 (with a Warning error message, and return is True) In case of error (not an Integer, or not 0/1 and exact True), Check is filled with a Fail (using mess) and return is False. More...

Standard_Boolean	ReadReal (const IGESData_ParamCursor &PC, Standard_Real &val)

Standard_Boolean	ReadReal (const IGESData_ParamCursor &PC, const Standard_CString mess, Standard_Real &val)
	Reads a Real value from parameter "num" An Integer is accepted (Check is filled with a Warning message) and causes return to be True (as normal case) In other cases, Check is filled with a Fail and return is False. More...

Standard_Boolean	ReadXY (const IGESData_ParamCursor &PC, Message_Msg &amsg, gp_XY &val)

Standard_Boolean	ReadXY (const IGESData_ParamCursor &PC, const Standard_CString mess, gp_XY &val)
	Reads a couple of Real values (X,Y) from parameter "num" Integers are accepted (Check is filled with a Warning message) and cause return to be True (as normal case) In other cases, Check is filled with a Fail and return is False. More...

Standard_Boolean	ReadXYZ (const IGESData_ParamCursor &PC, Message_Msg &amsg, gp_XYZ &val)

Standard_Boolean	ReadXYZ (const IGESData_ParamCursor &PC, const Standard_CString mess, gp_XYZ &val)
	Reads a triplet of Real values (X,Y,Z) from parameter "num" Integers are accepted (Check is filled with a Warning message) and cause return to be True (as normal case) In other cases, Check is filled with a Fail and return is False For Message. More...

Standard_Boolean	ReadText (const IGESData_ParamCursor &PC, const Message_Msg &amsg, Handle< TCollection_HAsciiString > &val)

Standard_Boolean	ReadText (const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< TCollection_HAsciiString > &val)
	Reads a Text value from parameter "num", as a String from Collection, that is, Hollerith text without leading "nnnH" If it is not a String, fills Check with a Fail (using mess) and returns False. More...

Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, IGESData_Status &aStatus, Handle< IGESData_IGESEntity > &val, const Standard_Boolean canbenul=Standard_False)

Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< IGESData_IGESEntity > &val, const Standard_Boolean canbenul=Standard_False)
	Reads an IGES entity from parameter "num" An Entity is known by its reference, which has the form of an odd Integer Value (a number in the Directory) If <canbenul> is given True, a Reference can also be Null : in this case, the result is a Null Handle with no Error If <canbenul> is False, a Null Reference causes an Error If the parameter cannot refer to an entity (or null), fills Check with a Fail (using mess) and returns False. More...

Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, IGESData_Status &aStatus, const Handle< Standard_Type > &type, Handle< IGESData_IGESEntity > &val, const Standard_Boolean canbenul=Standard_False)

template<class T >
Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, IGESData_Status &aStatus, const Handle< Standard_Type > &type, Handle< T > &val, const Standard_Boolean canbenul=Standard_False)
	Safe variant for arbitrary type of argument. More...

Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Standard_CString mess, const Handle< Standard_Type > &type, Handle< IGESData_IGESEntity > &val, const Standard_Boolean canbenul=Standard_False)
	Works as ReadEntity without Type, but in addition checks the Type of the Entity, which must be "kind of" a given <type> Then, gives the same fail cases as ReadEntity without Type, plus the case "Incorrect Type" (in such a case, returns False and givel <val> = Null) More...

template<class T >
Standard_Boolean	ReadEntity (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Standard_CString mess, const Handle< Standard_Type > &type, Handle< T > &val, const Standard_Boolean canbenul=Standard_False)
	Safe variant for arbitrary type of argument. More...

Standard_Boolean	ReadInts (const IGESData_ParamCursor &PC, const Message_Msg &amsg, Handle< TColStd_HArray1OfInteger > &val, const Standard_Integer index=1)

Standard_Boolean	ReadInts (const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< TColStd_HArray1OfInteger > &val, const Standard_Integer index=1)
	Reads a list of Integer values, defined by PC (with a count of parameters). PC can start from Current Number and command it to advance after reading (use method CurrentList to do this) The list is given as a HArray1, numered from "index" If all params are not Integer, Check is filled (using mess) and return value is False. More...

Standard_Boolean	ReadReals (const IGESData_ParamCursor &PC, Message_Msg &amsg, Handle< TColStd_HArray1OfReal > &val, const Standard_Integer index=1)

Standard_Boolean	ReadReals (const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< TColStd_HArray1OfReal > &val, const Standard_Integer index=1)
	Reads a list of Real values defined by PC Same conditions as for ReadInts, for PC and index An Integer parameter is accepted, if at least one parameter is Integer, Check is filled with a "Warning" message If all params are neither Real nor Integer, Check is filled (using mess) and return value is False. More...

Standard_Boolean	ReadTexts (const IGESData_ParamCursor &PC, const Message_Msg &amsg, Handle< Interface_HArray1OfHAsciiString > &val, const Standard_Integer index=1)

Standard_Boolean	ReadTexts (const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< Interface_HArray1OfHAsciiString > &val, const Standard_Integer index=1)
	Reads a list of Hollerith Texts, defined by PC Texts are read as Hollerith texts without leading "nnnH" Same conditions as for ReadInts, for PC and index If all params are not Text, Check is filled (using mess) and return value is False. More...

Standard_Boolean	ReadEnts (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Message_Msg &amsg, Handle< IGESData_HArray1OfIGESEntity > &val, const Standard_Integer index=1)

Standard_Boolean	ReadEnts (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Standard_CString mess, Handle< IGESData_HArray1OfIGESEntity > &val, const Standard_Integer index=1)
	Reads a list of Entities defined by PC Same conditions as for ReadInts, for PC and index The list is given as a HArray1, numered from "index" If all params cannot be read as Entities, Check is filled (using mess) and return value is False Remark : Null references are accepted, they are ignored (negative pointers too : they provoke a Warning message) If the caller wants to check them, a loop on ReadEntity should be used. More...

Standard_Boolean	ReadEntList (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, Message_Msg &amsg, Interface_EntityList &val, const Standard_Boolean ord=Standard_True)

Standard_Boolean	ReadEntList (const Handle< IGESData_IGESReaderData > &IR, const IGESData_ParamCursor &PC, const Standard_CString mess, Interface_EntityList &val, const Standard_Boolean ord=Standard_True)
	Reads a list of Entities defined by PC Same conditions as for ReadEnts, for PC The list is given as an EntityList (index has no meaning; the EntityList starts from clear) If "ord" is given True (default), entities will be added to the list in their original order Remark : Negative or Null Pointers are ignored Else ("ord" False), order is not guaranteed (faster mode) If all params cannot be read as Entities, same as above Warning Give "ord" to False ONLY if order is not significant. More...

Standard_Boolean	ReadingReal (const Standard_Integer num, Standard_Real &val)

Standard_Boolean	ReadingReal (const Standard_Integer num, const Standard_CString mess, Standard_Real &val)
	Routine which reads a Real parameter, given its number Same conditions as ReadReal for mess, val, and return value. More...

Standard_Boolean	ReadingEntityNumber (const Standard_Integer num, Standard_Integer &val)

Standard_Boolean	ReadingEntityNumber (const Standard_Integer num, const Standard_CString mess, Standard_Integer &val)
	Routine which reads an Entity Number (which allows to read the Entity in the IGESReaderData by BoundEntity), given its number in the list of Parameters Same conditions as ReadEntity for mess, val, and return value In particular, returns True and val to zero means Null Entity, and val not zero means Entity read by BoundEntity. More...

void	SendFail (const Message_Msg &amsg)

void	SendWarning (const Message_Msg &amsg)

void	AddFail (const Standard_CString afail, const Standard_CString bfail="")

void	AddFail (const Handle< TCollection_HAsciiString > &af, const Handle< TCollection_HAsciiString > &bf)
	feeds the Check with a new fail (as a String or as a CString) More...

void	AddWarning (const Standard_CString awarn, const Standard_CString bwarn="")

void	AddWarning (const Handle< TCollection_HAsciiString > &aw, const Handle< TCollection_HAsciiString > &bw)
	feeds the Check with a new Warning message More...

void	Mend (const Standard_CString pref="")

Standard_Boolean	HasFailed () const
	says if fails have been recorded into the Check More...

const Handle< Interface_Check > &	Check () const
	returns the Check Note that any error signaled above is also recorded into it More...

Handle< Interface_Check > &	CCheck ()
	returns the check in a way which allows to work on it directly (i.e. messages added to the Check are added to ParamReader too) More...

Standard_Boolean	IsCheckEmpty () const
	Returns True if the Check is Empty Else, it has to be recorded with the Read Entity. More...

Detailed Description

access to a list of parameters, with management of read stage (owned parameters, properties, associativities) and current parameter number, read errors (which feed a Check), plus convenient facilities to read parameters, in particular :

first parameter is ignored (it repeats entity type), hence number 1 gives 2nd parameter, etc...
lists are not explicit, list-reading methods are provided which manage a current param. number
interpretation is made as possible (texts, reals, entities ...) (in particular, Reading a Real accepts an Integer)

Constructor & Destructor Documentation

◆ IGESData_ParamReader()

IGESData_ParamReader::IGESData_ParamReader	(	const Handle< Interface_ParamList > &	list,
		const Handle< Interface_Check > &	ach,
		const Standard_Integer	base = `1`,
		const Standard_Integer	nbpar = `0`,
		const Standard_Integer	num = `0`
	)

Prepares a ParamReader, stage "Own", current param = 1 It considers a part of the list, from <base> (excluded) for <nbpar> parameters; <nbpar> = 0 commands to take list length. Default is (1 to skip type)

Member Function Documentation

◆ AddFail() [1/2]

void IGESData_ParamReader::AddFail	(	const Handle< TCollection_HAsciiString > &	af,
		const Handle< TCollection_HAsciiString > &	bf
	)

feeds the Check with a new fail (as a String or as a CString)

◆ AddFail() [2/2]

void IGESData_ParamReader::AddFail	(	const Standard_CString	afail,
		const Standard_CString	bfail = `""`
	)

◆ AddWarning() [1/2]

void IGESData_ParamReader::AddWarning	(	const Handle< TCollection_HAsciiString > &	aw,
		const Handle< TCollection_HAsciiString > &	bw
	)

feeds the Check with a new Warning message

◆ AddWarning() [2/2]

void IGESData_ParamReader::AddWarning	(	const Standard_CString	awarn,
		const Standard_CString	bwarn = `""`
	)

◆ CCheck()

Handle< Interface_Check >& IGESData_ParamReader::CCheck ( )

returns the check in a way which allows to work on it directly (i.e. messages added to the Check are added to ParamReader too)

◆ Check()

const Handle< Interface_Check >& IGESData_ParamReader::Check ( ) const

returns the Check Note that any error signaled above is also recorded into it

◆ Clear()

void IGESData_ParamReader::Clear ( )

resets state (stage, current param number, check with no fail)

◆ Current()

IGESData_ParamCursor IGESData_ParamReader::Current ( ) const

Creates a ParamCursor from the Current Number, to read one parameter, and to advance Current Number after reading.

◆ CurrentList()

IGESData_ParamCursor IGESData_ParamReader::CurrentList	(	const Standard_Integer	nb,
		const Standard_Integer	size = `1`
	)		const

Creates a ParamCursor from the Current Number, to read a list of "nb" items, and to advance Current Number after reading By default, each item is made of one parameter If size is given, it precises the number of params per item.

◆ CurrentNumber()

Standard_Integer IGESData_ParamReader::CurrentNumber ( ) const

returns the current parameter number This notion is involved by the organisation of an IGES list of parameter : it can be ended by two lists (Associativities and Properties), which can be empty, or even absent. Hence, it is necessary to know, at the end of specific reading, how many parameters have been read : the optional lists follow

◆ DefinedElseSkip()

Standard_Boolean IGESData_ParamReader::DefinedElseSkip ( )

Allows to simply process a parameter which can be defaulted. Waits on the Current Number a defined parameter or skips it : If the parameter <num> is defined, changes nothing and returns True Hence, the next reading with current cursor will concern <num> If it is void, advances Current Position by one, and returns False The next reading will concern <num+1> (except if <num> = NbParams)

This allows to process Default values as follows (C++) : if (PR.DefinedElseSkip()) { .. PR.Read... (current parameter); } else { <current parameter> = default value .. nothing else to do with ParamReader } For Message

◆ EndAll()

void IGESData_ParamReader::EndAll ( )

passes directly to the end of reading process

◆ EntityNumber()

Standard_Integer IGESData_ParamReader::EntityNumber ( ) const

Returns the entity number in the file.

◆ HasFailed()

Standard_Boolean IGESData_ParamReader::HasFailed ( ) const

says if fails have been recorded into the Check

◆ IsCheckEmpty()

Standard_Boolean IGESData_ParamReader::IsCheckEmpty ( ) const

Returns True if the Check is Empty Else, it has to be recorded with the Read Entity.

◆ IsParamDefined()

Standard_Boolean IGESData_ParamReader::IsParamDefined ( const Standard_Integer num ) const

says if a parameter is defined (not void) See also DefinedElseSkip

◆ IsParamEntity()

Standard_Boolean IGESData_ParamReader::IsParamEntity ( const Standard_Integer num ) const

says if a parameter can be regarded as an entity reference (see Prepare from IGESReaderData for more explanation) Note that such a parameter can seen as be a plain Integer too

◆ Mend()

void IGESData_ParamReader::Mend ( const Standard_CString pref = "" )

◆ NbParams()

Standard_Integer IGESData_ParamReader::NbParams ( ) const

returns number of parameters (minus the first one) following method skip the first parameter (1 gives the 2nd)

◆ NextStage()

void IGESData_ParamReader::NextStage ( )

passes to next stage (must be linked with setting Current)

◆ ParamEntity()

Handle< IGESData_IGESEntity > IGESData_ParamReader::ParamEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const Standard_Integer	num
	)

directly returns entity referenced by a parameter

◆ ParamNumber()

Standard_Integer IGESData_ParamReader::ParamNumber ( const Standard_Integer num ) const

returns entity number corresponding to a parameter if there is otherwise zero (according criterium IsParamEntity)

◆ ParamType()

Interface_ParamType IGESData_ParamReader::ParamType ( const Standard_Integer num ) const

returns type of parameter; note that "Ident" or "Sub" cannot be encountered, they correspond to "Integer", see also below

◆ ParamValue()

Standard_CString IGESData_ParamReader::ParamValue ( const Standard_Integer num ) const

returns literal value of a parameter, as it was in file

◆ ReadBoolean() [1/2]

Standard_Boolean IGESData_ParamReader::ReadBoolean	(	const IGESData_ParamCursor &	PC,
		const Message_Msg &	amsg,
		Standard_Boolean &	val,
		const Standard_Boolean	exact = `Standard_True`
	)

◆ ReadBoolean() [2/2]

Standard_Boolean IGESData_ParamReader::ReadBoolean	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Standard_Boolean &	val,
		const Standard_Boolean	exact = `Standard_True`
	)

Reads a Boolean value from parameter "num" A Boolean is given as an Integer value 0 (False) or 1 (True) Anyway, an Integer is demanded (else, Check is filled) If exact is given True, those precise values are demanded Else, Correction is done, as False for 0 or <0, True for >0 (with a Warning error message, and return is True) In case of error (not an Integer, or not 0/1 and exact True), Check is filled with a Fail (using mess) and return is False.

◆ ReadEntity() [1/6]

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		const Handle< Standard_Type > &	type,
		Handle< IGESData_IGESEntity > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

Works as ReadEntity without Type, but in addition checks the Type of the Entity, which must be "kind of" a given <type> Then, gives the same fail cases as ReadEntity without Type, plus the case "Incorrect Type" (in such a case, returns False and givel <val> = Null)

◆ ReadEntity() [2/6]

template<class T >

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		const Handle< Standard_Type > &	type,
		Handle< T > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

inline

Safe variant for arbitrary type of argument.

◆ ReadEntity() [3/6]

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< IGESData_IGESEntity > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

Reads an IGES entity from parameter "num" An Entity is known by its reference, which has the form of an odd Integer Value (a number in the Directory) If <canbenul> is given True, a Reference can also be Null : in this case, the result is a Null Handle with no Error If <canbenul> is False, a Null Reference causes an Error If the parameter cannot refer to an entity (or null), fills Check with a Fail (using mess) and returns False.

◆ ReadEntity() [4/6]

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		IGESData_Status &	aStatus,
		const Handle< Standard_Type > &	type,
		Handle< IGESData_IGESEntity > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

◆ ReadEntity() [5/6]

template<class T >

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		IGESData_Status &	aStatus,
		const Handle< Standard_Type > &	type,
		Handle< T > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

inline

Safe variant for arbitrary type of argument.

◆ ReadEntity() [6/6]

Standard_Boolean IGESData_ParamReader::ReadEntity	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		IGESData_Status &	aStatus,
		Handle< IGESData_IGESEntity > &	val,
		const Standard_Boolean	canbenul = `Standard_False`
	)

◆ ReadEntList() [1/2]

Standard_Boolean IGESData_ParamReader::ReadEntList	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Interface_EntityList &	val,
		const Standard_Boolean	ord = `Standard_True`
	)

Reads a list of Entities defined by PC Same conditions as for ReadEnts, for PC The list is given as an EntityList (index has no meaning; the EntityList starts from clear) If "ord" is given True (default), entities will be added to the list in their original order Remark : Negative or Null Pointers are ignored Else ("ord" False), order is not guaranteed (faster mode) If all params cannot be read as Entities, same as above Warning Give "ord" to False ONLY if order is not significant.

◆ ReadEntList() [2/2]

Standard_Boolean IGESData_ParamReader::ReadEntList	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		Message_Msg &	amsg,
		Interface_EntityList &	val,
		const Standard_Boolean	ord = `Standard_True`
	)

◆ ReadEnts() [1/2]

Standard_Boolean IGESData_ParamReader::ReadEnts	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Message_Msg &	amsg,
		Handle< IGESData_HArray1OfIGESEntity > &	val,
		const Standard_Integer	index = `1`
	)

◆ ReadEnts() [2/2]

Standard_Boolean IGESData_ParamReader::ReadEnts	(	const Handle< IGESData_IGESReaderData > &	IR,
		const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< IGESData_HArray1OfIGESEntity > &	val,
		const Standard_Integer	index = `1`
	)

Reads a list of Entities defined by PC Same conditions as for ReadInts, for PC and index The list is given as a HArray1, numered from "index" If all params cannot be read as Entities, Check is filled (using mess) and return value is False Remark : Null references are accepted, they are ignored (negative pointers too : they provoke a Warning message) If the caller wants to check them, a loop on ReadEntity should be used.

◆ ReadingEntityNumber() [1/2]

Standard_Boolean IGESData_ParamReader::ReadingEntityNumber	(	const Standard_Integer	num,
		const Standard_CString	mess,
		Standard_Integer &	val
	)

Routine which reads an Entity Number (which allows to read the Entity in the IGESReaderData by BoundEntity), given its number in the list of Parameters Same conditions as ReadEntity for mess, val, and return value In particular, returns True and val to zero means Null Entity, and val not zero means Entity read by BoundEntity.

◆ ReadingEntityNumber() [2/2]

Standard_Boolean IGESData_ParamReader::ReadingEntityNumber	(	const Standard_Integer	num,
		Standard_Integer &	val
	)

◆ ReadingReal() [1/2]

Standard_Boolean IGESData_ParamReader::ReadingReal	(	const Standard_Integer	num,
		const Standard_CString	mess,
		Standard_Real &	val
	)

Routine which reads a Real parameter, given its number Same conditions as ReadReal for mess, val, and return value.

◆ ReadingReal() [2/2]

Standard_Boolean IGESData_ParamReader::ReadingReal	(	const Standard_Integer	num,
		Standard_Real &	val
	)

◆ ReadInteger() [1/2]

Standard_Boolean IGESData_ParamReader::ReadInteger	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Standard_Integer &	val
	)

Reads an Integer value designated by PC The method Current designates the current parameter and advances the Current Number by one after reading Note that if a count (not 1) is given, it is ignored If it is not an Integer, fills Check with a Fail (using mess) and returns False.

◆ ReadInteger() [2/2]

Standard_Boolean IGESData_ParamReader::ReadInteger	(	const IGESData_ParamCursor &	PC,
		Standard_Integer &	val
	)

◆ ReadInts() [1/2]

Standard_Boolean IGESData_ParamReader::ReadInts	(	const IGESData_ParamCursor &	PC,
		const Message_Msg &	amsg,
		Handle< TColStd_HArray1OfInteger > &	val,
		const Standard_Integer	index = `1`
	)

◆ ReadInts() [2/2]

Standard_Boolean IGESData_ParamReader::ReadInts	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< TColStd_HArray1OfInteger > &	val,
		const Standard_Integer	index = `1`
	)

Reads a list of Integer values, defined by PC (with a count of parameters). PC can start from Current Number and command it to advance after reading (use method CurrentList to do this) The list is given as a HArray1, numered from "index" If all params are not Integer, Check is filled (using mess) and return value is False.

◆ ReadReal() [1/2]

Standard_Boolean IGESData_ParamReader::ReadReal	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Standard_Real &	val
	)

Reads a Real value from parameter "num" An Integer is accepted (Check is filled with a Warning message) and causes return to be True (as normal case) In other cases, Check is filled with a Fail and return is False.

◆ ReadReal() [2/2]

Standard_Boolean IGESData_ParamReader::ReadReal	(	const IGESData_ParamCursor &	PC,
		Standard_Real &	val
	)

◆ ReadReals() [1/2]

Standard_Boolean IGESData_ParamReader::ReadReals	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< TColStd_HArray1OfReal > &	val,
		const Standard_Integer	index = `1`
	)

Reads a list of Real values defined by PC Same conditions as for ReadInts, for PC and index An Integer parameter is accepted, if at least one parameter is Integer, Check is filled with a "Warning" message If all params are neither Real nor Integer, Check is filled (using mess) and return value is False.

◆ ReadReals() [2/2]

Standard_Boolean IGESData_ParamReader::ReadReals	(	const IGESData_ParamCursor &	PC,
		Message_Msg &	amsg,
		Handle< TColStd_HArray1OfReal > &	val,
		const Standard_Integer	index = `1`
	)

◆ ReadText() [1/2]

Standard_Boolean IGESData_ParamReader::ReadText	(	const IGESData_ParamCursor &	PC,
		const Message_Msg &	amsg,
		Handle< TCollection_HAsciiString > &	val
	)

◆ ReadText() [2/2]

Standard_Boolean IGESData_ParamReader::ReadText	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< TCollection_HAsciiString > &	val
	)

Reads a Text value from parameter "num", as a String from Collection, that is, Hollerith text without leading "nnnH" If it is not a String, fills Check with a Fail (using mess) and returns False.

◆ ReadTexts() [1/2]

Standard_Boolean IGESData_ParamReader::ReadTexts	(	const IGESData_ParamCursor &	PC,
		const Message_Msg &	amsg,
		Handle< Interface_HArray1OfHAsciiString > &	val,
		const Standard_Integer	index = `1`
	)

◆ ReadTexts() [2/2]

Standard_Boolean IGESData_ParamReader::ReadTexts	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		Handle< Interface_HArray1OfHAsciiString > &	val,
		const Standard_Integer	index = `1`
	)

Reads a list of Hollerith Texts, defined by PC Texts are read as Hollerith texts without leading "nnnH" Same conditions as for ReadInts, for PC and index If all params are not Text, Check is filled (using mess) and return value is False.

◆ ReadXY() [1/2]

Standard_Boolean IGESData_ParamReader::ReadXY	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		gp_XY &	val
	)

Reads a couple of Real values (X,Y) from parameter "num" Integers are accepted (Check is filled with a Warning message) and cause return to be True (as normal case) In other cases, Check is filled with a Fail and return is False.

◆ ReadXY() [2/2]

Standard_Boolean IGESData_ParamReader::ReadXY	(	const IGESData_ParamCursor &	PC,
		Message_Msg &	amsg,
		gp_XY &	val
	)

◆ ReadXYZ() [1/2]

Standard_Boolean IGESData_ParamReader::ReadXYZ	(	const IGESData_ParamCursor &	PC,
		const Standard_CString	mess,
		gp_XYZ &	val
	)

Reads a triplet of Real values (X,Y,Z) from parameter "num" Integers are accepted (Check is filled with a Warning message) and cause return to be True (as normal case) In other cases, Check is filled with a Fail and return is False For Message.

◆ ReadXYZ() [2/2]

Standard_Boolean IGESData_ParamReader::ReadXYZ	(	const IGESData_ParamCursor &	PC,
		Message_Msg &	amsg,
		gp_XYZ &	val
	)

◆ SendFail()

void IGESData_ParamReader::SendFail ( const Message_Msg & amsg )

◆ SendWarning()

void IGESData_ParamReader::SendWarning ( const Message_Msg & amsg )

◆ SetCurrentNumber()

void IGESData_ParamReader::SetCurrentNumber ( const Standard_Integer num )

sets current parameter number to a new value must be done at end of each step : set on first parameter following last read one; is done by some Read... methods (must be done directly if these method are not used) num greater than NbParams means that following lists are empty If current num is not managed, it remains at 1, which probably will cause error when successive steps of reading are made

◆ Stage()

IGESData_ReadStage IGESData_ParamReader::Stage ( ) const

gives current stage (Own-Props-Assocs-End, begins at Own)

The documentation for this class was generated from the following file:

IGESData_ParamReader.hxx

IGESData_ParamReader Class Reference

Public Member Functions