API giving the following geometric information about fillets list of corresponding NUBS surfaces for each surface: the 2 support faces on each face: the 3d curve and the corresponding 2d curve the 2d curves on the fillet status of start and end section of the fillet first and last parameter on edge of the fillet. More...

#include <FilletSurf_Builder.hxx>

Public Member Functions
	FilletSurf_Builder (const TopoDS_Shape &S, const TopTools_ListOfShape &E, const Standard_Real R, const Standard_Real Ta=1.0e-2, const Standard_Real Tapp3d=1.0e-4, const Standard_Real Tapp2d=1.0e-5)
	initialize of the information necessary for the computation of the fillet on the Shape S from a list of edges E and a radius R. More...

void	Perform ()
	—Purpose computation of the fillet (list of NUBS) More...

void	Simulate ()

FilletSurf_StatusDone	IsDone () const
	gives the status about the computation of the fillet returns: IsOK :no problem during the computation IsNotOk: no result is produced IsPartial: the result is partial More...

FilletSurf_ErrorTypeStatus	StatusError () const
	gives information about error status if IsDone=IsNotOk returns EdgeNotG1: the edges are not G1 FacesNotG1 : two connected faces on a same support are not G1 EdgeNotOnShape: the edge is not on shape NotSharpEdge: the edge is not sharp PbFilletCompute: problem during the computation of the fillet More...

Standard_Integer	NbSurface () const
	gives the number of NUBS surfaces of the Fillet. More...

const Handle< Geom_Surface > &	SurfaceFillet (const Standard_Integer Index) const
	gives the NUBS surface of index Index. More...

Standard_Real	TolApp3d (const Standard_Integer Index) const
	gives the 3d tolerance reached during approximation of surface of index Index More...

const TopoDS_Face &	SupportFace1 (const Standard_Integer Index) const
	gives the first support face relative to SurfaceFillet(Index); More...

const TopoDS_Face &	SupportFace2 (const Standard_Integer Index) const
	gives the second support face relative to SurfaceFillet(Index); More...

const Handle< Geom_Curve > &	CurveOnFace1 (const Standard_Integer Index) const
	gives the 3d curve of SurfaceFillet(Index) on SupportFace1(Index) More...

const Handle< Geom_Curve > &	CurveOnFace2 (const Standard_Integer Index) const
	gives the 3d curve of SurfaceFillet(Index) on SupportFace2(Index) More...

const Handle< Geom2d_Curve > &	PCurveOnFace1 (const Standard_Integer Index) const
	gives the PCurve associated to CurvOnSup1(Index) on the support face More...

const Handle< Geom2d_Curve > &	PCurve1OnFillet (const Standard_Integer Index) const
	gives the PCurve associated to CurveOnFace1(Index) on the Fillet More...

const Handle< Geom2d_Curve > &	PCurveOnFace2 (const Standard_Integer Index) const
	gives the PCurve associated to CurveOnSup2(Index) on the support face More...

const Handle< Geom2d_Curve > &	PCurve2OnFillet (const Standard_Integer Index) const
	gives the PCurve associated to CurveOnSup2(Index) on the fillet More...

Standard_Real	FirstParameter () const
	gives the parameter of the fillet on the first edge. More...

Standard_Real	LastParameter () const
	gives the parameter of the fillet on the last edge More...

FilletSurf_StatusType	StartSectionStatus () const

FilletSurf_StatusType	EndSectionStatus () const

Standard_Integer	NbSection (const Standard_Integer IndexSurf) const

void	Section (const Standard_Integer IndexSurf, const Standard_Integer IndexSec, Handle< Geom_TrimmedCurve > &Circ) const

Detailed Description

API giving the following geometric information about fillets list of corresponding NUBS surfaces for each surface: the 2 support faces on each face: the 3d curve and the corresponding 2d curve the 2d curves on the fillet status of start and end section of the fillet first and last parameter on edge of the fillet.

Constructor & Destructor Documentation

◆ FilletSurf_Builder()

FilletSurf_Builder::FilletSurf_Builder	(	const TopoDS_Shape &	S,
		const TopTools_ListOfShape &	E,
		const Standard_Real	R,
		const Standard_Real	Ta = `1.0e-2`,
		const Standard_Real	Tapp3d = `1.0e-4`,
		const Standard_Real	Tapp2d = `1.0e-5`
	)

initialize of the information necessary for the computation of the fillet on the Shape S from a list of edges E and a radius R.

Ta is the angular tolerance Tapp3d is the 3d approximation tolerance Tapp2d is the 2d approximation tolerance

Member Function Documentation

◆ CurveOnFace1()

const Handle< Geom_Curve >& FilletSurf_Builder::CurveOnFace1 ( const Standard_Integer Index ) const

gives the 3d curve of SurfaceFillet(Index) on SupportFace1(Index)

◆ CurveOnFace2()

const Handle< Geom_Curve >& FilletSurf_Builder::CurveOnFace2 ( const Standard_Integer Index ) const

gives the 3d curve of SurfaceFillet(Index) on SupportFace2(Index)

◆ EndSectionStatus()

FilletSurf_StatusType FilletSurf_Builder::EndSectionStatus ( ) const

◆ FirstParameter()

Standard_Real FilletSurf_Builder::FirstParameter ( ) const

gives the parameter of the fillet on the first edge.

◆ IsDone()

FilletSurf_StatusDone FilletSurf_Builder::IsDone ( ) const

gives the status about the computation of the fillet returns: IsOK :no problem during the computation IsNotOk: no result is produced IsPartial: the result is partial

◆ LastParameter()

Standard_Real FilletSurf_Builder::LastParameter ( ) const

gives the parameter of the fillet on the last edge

◆ NbSection()

Standard_Integer FilletSurf_Builder::NbSection ( const Standard_Integer IndexSurf ) const

◆ NbSurface()

Standard_Integer FilletSurf_Builder::NbSurface ( ) const

gives the number of NUBS surfaces of the Fillet.

◆ PCurve1OnFillet()

const Handle< Geom2d_Curve >& FilletSurf_Builder::PCurve1OnFillet ( const Standard_Integer Index ) const

gives the PCurve associated to CurveOnFace1(Index) on the Fillet

◆ PCurve2OnFillet()

const Handle< Geom2d_Curve >& FilletSurf_Builder::PCurve2OnFillet ( const Standard_Integer Index ) const

gives the PCurve associated to CurveOnSup2(Index) on the fillet

◆ PCurveOnFace1()

const Handle< Geom2d_Curve >& FilletSurf_Builder::PCurveOnFace1 ( const Standard_Integer Index ) const

gives the PCurve associated to CurvOnSup1(Index) on the support face

◆ PCurveOnFace2()

const Handle< Geom2d_Curve >& FilletSurf_Builder::PCurveOnFace2 ( const Standard_Integer Index ) const

gives the PCurve associated to CurveOnSup2(Index) on the support face

◆ Perform()

void FilletSurf_Builder::Perform ( )

—Purpose computation of the fillet (list of NUBS)

◆ Section()

void FilletSurf_Builder::Section	(	const Standard_Integer	IndexSurf,
		const Standard_Integer	IndexSec,
		Handle< Geom_TrimmedCurve > &	Circ
	)		const

◆ Simulate()

void FilletSurf_Builder::Simulate ( )

◆ StartSectionStatus()

FilletSurf_StatusType FilletSurf_Builder::StartSectionStatus ( ) const

◆ StatusError()

FilletSurf_ErrorTypeStatus FilletSurf_Builder::StatusError ( ) const

gives information about error status if IsDone=IsNotOk returns EdgeNotG1: the edges are not G1 FacesNotG1 : two connected faces on a same support are not G1 EdgeNotOnShape: the edge is not on shape NotSharpEdge: the edge is not sharp PbFilletCompute: problem during the computation of the fillet

◆ SupportFace1()

const TopoDS_Face& FilletSurf_Builder::SupportFace1 ( const Standard_Integer Index ) const

gives the first support face relative to SurfaceFillet(Index);

◆ SupportFace2()

const TopoDS_Face& FilletSurf_Builder::SupportFace2 ( const Standard_Integer Index ) const

gives the second support face relative to SurfaceFillet(Index);

◆ SurfaceFillet()

const Handle< Geom_Surface >& FilletSurf_Builder::SurfaceFillet ( const Standard_Integer Index ) const

gives the NUBS surface of index Index.

◆ TolApp3d()

Standard_Real FilletSurf_Builder::TolApp3d ( const Standard_Integer Index ) const

gives the 3d tolerance reached during approximation of surface of index Index

The documentation for this class was generated from the following file:

FilletSurf_Builder.hxx

Public Member Functions