This class provides the bisecting line between two geometric elements.The elements are Circles,Lines or Points.
More...
|
| Bisector_BisecAna () |
|
void | Perform (const Handle< Geom2d_Curve > &Cu1, const Handle< Geom2d_Curve > &Cu2, const gp_Pnt2d &P, const gp_Vec2d &V1, const gp_Vec2d &V2, const Standard_Real Sense, const GeomAbs_JoinType jointype, const Standard_Real Tolerance, const Standard_Boolean oncurve=Standard_True) |
| Performs the bisecting line between the curves <Cu1> and <Cu2>. <oncurve> is True if the point. More...
|
|
void | Perform (const Handle< Geom2d_Curve > &Cu, const Handle< Geom2d_Point > &Pnt, const gp_Pnt2d &P, const gp_Vec2d &V1, const gp_Vec2d &V2, const Standard_Real Sense, const Standard_Real Tolerance, const Standard_Boolean oncurve=Standard_True) |
| Performs the bisecting line between the curve <Cu1> and the point <Pnt>. <oncurve> is True if the point. More...
|
|
void | Perform (const Handle< Geom2d_Point > &Pnt, const Handle< Geom2d_Curve > &Cu, const gp_Pnt2d &P, const gp_Vec2d &V1, const gp_Vec2d &V2, const Standard_Real Sense, const Standard_Real Tolerance, const Standard_Boolean oncurve=Standard_True) |
| Performs the bisecting line between the curve <Cu> and the point <Pnt>. <oncurve> is True if the point. More...
|
|
void | Perform (const Handle< Geom2d_Point > &Pnt1, const Handle< Geom2d_Point > &Pnt2, const gp_Pnt2d &P, const gp_Vec2d &V1, const gp_Vec2d &V2, const Standard_Real Sense, const Standard_Real Tolerance=0.0, const Standard_Boolean oncurve=Standard_True) |
| Performs the bisecting line between the two points <Pnt1> and <Pnt2>. More...
|
|
void | Init (const Handle< Geom2d_TrimmedCurve > &bisector) |
|
Standard_Boolean | IsExtendAtStart () const override |
|
Standard_Boolean | IsExtendAtEnd () const override |
|
void | SetTrim (const Handle< Geom2d_Curve > &Cu) |
| Trim <me> by a domain defined by the curve <Cu>. This domain is the set of the points which are nearest from <Cu> than the extremitis of <Cu>. More...
|
|
void | SetTrim (const Standard_Real uf, const Standard_Real ul) |
| Trim <me> by a domain defined by uf and ul. More...
|
|
void | Reverse () override |
| Changes the direction of parametrization of <me>. The "FirstParameter" and the "LastParameter" are not changed but the orientation of the curve is modified. If the curve is bounded the StartPoint of the initial curve becomes the EndPoint of the reversed curve and the EndPoint of the initial curve becomes the StartPoint of the reversed curve. More...
|
|
Standard_Real | ReversedParameter (const Standard_Real U) const override |
| Computes the parameter on the reversed curve for the point of parameter U on this curve. Note: The point of parameter U on this curve is identical to the point of parameter ReversedParameter(U) on the reversed curve. More...
|
|
Standard_Boolean | IsCN (const Standard_Integer N) const override |
| Returns the order of continuity of the curve. Raised if N < 0. More...
|
|
Handle< Geom2d_Geometry > | Copy () const override |
|
void | Transform (const gp_Trsf2d &T) override |
| Transformation of a geometric object. This tansformation can be a translation, a rotation, a symmetry, a scaling or a complex transformation obtained by combination of the previous elementaries transformations. (see class Transformation of the package Geom2d). The following transformations have the same properties as the previous ones but they don't modified the object itself. A copy of the object is returned. More...
|
|
Standard_Real | FirstParameter () const override |
| Returns the value of the first parameter. Warnings : It can be RealFirst or RealLast from package Standard if the curve is infinite. More...
|
|
Standard_Real | LastParameter () const override |
| Value of the last parameter. Warnings : It can be RealFirst or RealLast from package Standard if the curve is infinite. More...
|
|
Standard_Boolean | IsClosed () const override |
| Returns true if the curve is closed. Examples : Some curves such as circle are always closed, others such as line are never closed (by definition). Some Curves such as OffsetCurve can be closed or not. These curves are considered as closed if the distance between the first point and the last point of the curve is lower or equal to the Resolution from package gp which is a fixed criterion independent of the application. More...
|
|
Standard_Boolean | IsPeriodic () const override |
| Returns true if the parameter of the curve is periodic. It is possible only if the curve is closed and if the following relation is satisfied : for each parametric value U the distance between the point P(u) and the point P (u + T) is lower or equal to Resolution from package gp, T is the period and must be a constant. There are three possibilities : . the curve is never periodic by definition (SegmentLine) . the curve is always periodic by definition (Circle) . the curve can be defined as periodic (BSpline). In this case a function SetPeriodic allows you to give the shape of the curve. The general rule for this case is : if a curve can be periodic or not the default periodicity set is non periodic and you have to turn (explicitly) the curve into a periodic curve if you want the curve to be periodic. More...
|
|
GeomAbs_Shape | Continuity () const override |
| It is the global continuity of the curve : C0 : only geometric continuity, C1 : continuity of the first derivative all along the Curve, C2 : continuity of the second derivative all along the Curve, C3 : continuity of the third derivative all along the Curve, G1 : tangency continuity all along the Curve, G2 : curvature continuity all along the Curve, CN : the order of continuity is infinite. More...
|
|
void | D0 (const Standard_Real U, gp_Pnt2d &P) const override |
| Returns in P the point of parameter U. If the curve is periodic then the returned point is P(U) with U = Ustart + (U - Uend) where Ustart and Uend are the parametric bounds of the curve. More...
|
|
void | D1 (const Standard_Real U, gp_Pnt2d &P, gp_Vec2d &V1) const override |
| Returns the point P of parameter U and the first derivative V1. Raised if the continuity of the curve is not C1. More...
|
|
void | D2 (const Standard_Real U, gp_Pnt2d &P, gp_Vec2d &V1, gp_Vec2d &V2) const override |
| Returns the point P of parameter U, the first and second derivatives V1 and V2. Raised if the continuity of the curve is not C2. More...
|
|
void | D3 (const Standard_Real U, gp_Pnt2d &P, gp_Vec2d &V1, gp_Vec2d &V2, gp_Vec2d &V3) const override |
| Returns the point P of parameter U, the first, the second and the third derivative. Raised if the continuity of the curve is not C3. More...
|
|
gp_Vec2d | DN (const Standard_Real U, const Standard_Integer N) const override |
| For the point of parameter U of this curve, computes the vector corresponding to the Nth derivative. Exceptions StdFail_UndefinedDerivative if: More...
|
|
Handle< Geom2d_Curve > | Geom2dCurve () const |
|
Standard_Real | Parameter (const gp_Pnt2d &P) const override |
|
Standard_Real | ParameterOfStartPoint () const |
|
Standard_Real | ParameterOfEndPoint () const |
|
Standard_Integer | NbIntervals () const override |
| If necessary, breaks the curve in intervals of continuity <C1>. And returns the number of intervals. More...
|
|
Standard_Real | IntervalFirst (const Standard_Integer Index) const override |
| Returns the first parameter of the current interval. More...
|
|
Standard_Real | IntervalLast (const Standard_Integer Index) const override |
| Returns the last parameter of the current interval. More...
|
|
void | Dump (const Standard_Integer Deep=0, const Standard_Integer Offset=0) const |
|
virtual Standard_Real | TransformedParameter (const Standard_Real U, const gp_Trsf2d &T) const |
| Computes the parameter on the curve transformed by T for the point of parameter U on this curve. Note: this function generally returns U but it can be redefined (for example, on a line). More...
|
|
virtual Standard_Real | ParametricTransformation (const gp_Trsf2d &T) const |
| Returns the coefficient required to compute the parametric transformation of this curve when transformation T is applied. This coefficient is the ratio between the parameter of a point on this curve and the parameter of the transformed point on the new curve transformed by T. Note: this function generally returns 1. but it can be redefined (for example, on a line). More...
|
|
Handle< Geom2d_Curve > | Reversed () const |
| Creates a reversed duplicate Changes the orientation of this curve. The first and last parameters are not changed, but the parametric direction of the curve is reversed. If the curve is bounded: More...
|
|
virtual Standard_Real | Period () const |
| Returns the period of this curve. raises if the curve is not periodic. More...
|
|
gp_Pnt2d | Value (const Standard_Real U) const |
| Computes the point of parameter U on <me>. If the curve is periodic then the returned point is P(U) with U = Ustart + (U - Uend) where Ustart and Uend are the parametric bounds of the curve. More...
|
|
virtual void | DumpJson (Standard_OStream &theOStream, Standard_Integer theDepth=-1) const override |
| Dumps the content of me into the stream. More...
|
|
void | Mirror (const gp_Pnt2d &P) |
| Performs the symmetrical transformation of a Geometry with respect to the point P which is the center of the symmetry and assigns the result to this geometric object. More...
|
|
void | Mirror (const gp_Ax2d &A) |
| Performs the symmetrical transformation of a Geometry with respect to an axis placement which is the axis of the symmetry. More...
|
|
void | Rotate (const gp_Pnt2d &P, const Standard_Real Ang) |
| Rotates a Geometry. P is the center of the rotation. Ang is the angular value of the rotation in radians. More...
|
|
void | Scale (const gp_Pnt2d &P, const Standard_Real S) |
| Scales a Geometry. S is the scaling value. More...
|
|
void | Translate (const gp_Vec2d &V) |
| Translates a Geometry. V is the vector of the translation. More...
|
|
void | Translate (const gp_Pnt2d &P1, const gp_Pnt2d &P2) |
| Translates a Geometry from the point P1 to the point P2. More...
|
|
Handle< Geom2d_Geometry > | Mirrored (const gp_Pnt2d &P) const |
|
Handle< Geom2d_Geometry > | Mirrored (const gp_Ax2d &A) const |
|
Handle< Geom2d_Geometry > | Rotated (const gp_Pnt2d &P, const Standard_Real Ang) const |
|
Handle< Geom2d_Geometry > | Scaled (const gp_Pnt2d &P, const Standard_Real S) const |
|
Handle< Geom2d_Geometry > | Transformed (const gp_Trsf2d &T) const |
|
Handle< Geom2d_Geometry > | Translated (const gp_Vec2d &V) const |
|
Handle< Geom2d_Geometry > | Translated (const gp_Pnt2d &P1, const gp_Pnt2d &P2) const |
|
Public Member Functions inherited from Standard_Transient |
| Standard_Transient () |
| Empty constructor. More...
|
|
| Standard_Transient (const Standard_Transient &) |
| Copy constructor – does nothing. More...
|
|
Standard_Transient & | operator= (const Standard_Transient &) |
| Assignment operator, needed to avoid copying reference counter. More...
|
|
virtual | ~Standard_Transient () |
| Destructor must be virtual. More...
|
|
virtual void | Delete () const |
| Memory deallocator for transient classes. More...
|
|
virtual const opencascade::handle< Standard_Type > & | DynamicType () const |
| Returns a type descriptor about this object. More...
|
|
Standard_Boolean | IsInstance (const opencascade::handle< Standard_Type > &theType) const |
| Returns a true value if this is an instance of Type. More...
|
|
Standard_Boolean | IsInstance (const Standard_CString theTypeName) const |
| Returns a true value if this is an instance of TypeName. More...
|
|
Standard_Boolean | IsKind (const opencascade::handle< Standard_Type > &theType) const |
| Returns true if this is an instance of Type or an instance of any class that inherits from Type. Note that multiple inheritance is not supported by OCCT RTTI mechanism. More...
|
|
Standard_Boolean | IsKind (const Standard_CString theTypeName) const |
| Returns true if this is an instance of TypeName or an instance of any class that inherits from TypeName. Note that multiple inheritance is not supported by OCCT RTTI mechanism. More...
|
|
Standard_Transient * | This () const |
| Returns non-const pointer to this object (like const_cast). For protection against creating handle to objects allocated in stack or call from constructor, it will raise exception Standard_ProgramError if reference counter is zero. More...
|
|
Standard_Integer | GetRefCount () const |
| Get the reference counter of this object. More...
|
|
void | IncrementRefCounter () const |
| Increments the reference counter of this object. More...
|
|
Standard_Integer | DecrementRefCounter () const |
| Decrements the reference counter of this object; returns the decremented value. More...
|
|
This class provides the bisecting line between two geometric elements.The elements are Circles,Lines or Points.